A storage tank connects to pipes and stores fluid. The tank does not produce fluid by itself or keep sending it in one direction. Start with one tank connected to a pipe for a single fluid, then check its contents and connections.
This guide covers the base game on PC version 2.0.77, at normal quality, without Space Age or mods. Materials, research, capacity, and connection points are checked against version-pinned developer data; use is referenced against the official wiki, which is community-edited. In-game controls and throughput measurements were not tested. Quality-specific capacity, display, and circuit features added in Wiki version 2.1 are not included.
Materials and research for one tank
| Item | Amount or requirement for 1 | Check |
|---|---|---|
| Iron plates | 20 | Direct ingredients for the tank |
| Steel | 5 | Separate ingredient from iron plates |
| Research | Fluid handling | Requires Automation 2 and Engine |
| Science packs | 50 red and 50 green | For Fluid handling itself; prerequisite research is separate |
| Pipes | Additional, depending on placement distance | Not included in the tank's cost |
Fluid handling also unlocks pumps and empty barrels, as well as storage tanks. If labs do not have science packs, check the supply for Red Science and Green Science. This guide does not calculate the shortest research time or total costs including prerequisites.
In version 2.0.77, one tank has a capacity of 25,000 and occupies a 3×3 area. Use one tank to check whether the contents rise before adding more; this is not an optimization for the ideal storage capacity.
Connect one tank to pipes
This example connects a tank to a short water pipe. The same idea of separating fluid types applies to oil processing, but each refinery output must be handled separately.
- Complete Fluid handling, then craft one tank from 20 iron plates and 5 steel.
- Check the water pipe coming from an offshore pump or other source. Leave a gap from pipes carrying different fluids.
- Place the tank and connect pipes at one of its connection points. Do not assume every edge of the 3×3 footprint connects.
- Check the fluid type and amount in the pipe and tank GUIs. If it is empty, trace the pipe from the source to the tank.
- Extend the pipe to equipment that uses the same water, then observe the amount as supply and consumption run. You do not need to designate a fixed inlet and outlet.
A tank increases the capacity of its connected pipe segment. Pipes and tanks in the same segment share the same fill percentage; multiple connected tanks do not fill one at a time from the first tank onward. Think about capacity separately from the fluid production rate.
Distinguish no fluid, no output, and a full tank
| Situation | Check first | Next step |
|---|---|---|
| Cannot craft it | Fluid handling and ingredients | Check prerequisite research, 20 iron plates, and 5 steel |
| Only the tank is empty | Actual connection points and fluid | Check that it is on the same connected pipe segment |
| Amount rises, then drops | Downstream consumption | Observe production and consumption separately |
| Fluid is in the tank but does not move onward | Pipes and an intermediate pump | Check the pump's power, direction, and circuit conditions |
| Production stops when the tank is full | Where the fluid can go | Check consumers and blocked outputs elsewhere |
An intermediate pump will not move fluid without power, and if it has a circuit condition it will only pass fluid when the condition is met. A storage tank is passive, so do not confuse bringing a power pole near the tank with powering a pump along the pipe.
Adding more tanks while they are full can increase storage capacity, but it may not fix a persistent imbalance between production and consumption. If you use heavy oil or light oil or set up cracking, also check the other outputs in What to Do When Oil Products Back Up.
If you need to keep the fluid
Removing fluid through the tank or pipe GUI does not recover it. When correcting a bad connection, first separate the pipes and check the fluid type. If you need to move the contents, use a pump to send them to another storage location, after checking that the destination has room and is for the right fluid.
This guide does not guarantee what happens to the fluid when a tank is removed. Do not rely on GUI deletion or removal to test a transfer; prepare a destination before moving fluid you need. When you are ready to transport oil from far away, continue to Loading and Unloading a Fluid Wagon.
For one-way flow to a destination, check Pump Direction, Power, and a Clear Outlet.
Sources and references
Questions and contributions
Share questions, corrections or play reports. Only approved posts for this article and language appear here.
Submit for review
Do not include personal details, passwords or private information about others. Text only. Publication and replies are not guaranteed.