Scope: PC full release 1.2 series, standard recipes, 100% clock speed, no production amplification, and no mods.
Unlock Part Assembly and make the first construction materials at a Craft Bench
Finish HUB Upgrade 6 and select “Part Assembly” in Tier 2. Submit 200 Cable, 200 Iron Rods, 500 Screws, and 300 Iron Plates, then complete the launch action at the terminal.
Building one Assembler costs 8 Reinforced Iron Plates, 4 Rotors, and 10 Cable. You need Reinforced Iron Plates to build the machine that will mass-produce them, but you can make the initial amount at a Craft Bench. You also need to craft the Rotors at the Craft Bench after completing Part Assembly.
The Constructor and Assembler are different machines. Putting Iron Plates or Screws into a Constructor will not make the standard Reinforced Iron Plate recipe.
Check that one item can be made by hand-feeding the inputs
- Build the Assembler and connect a Power Line from a Power Pole.
- Press E to open its interface.
- Select the standard “Reinforced Iron Plate” recipe.
- Put 6 Iron Plates and 12 Screws into the input slots.
- Check that it is not on standby and wait for production to progress.
- Confirm that 1 Reinforced Iron Plate appears in the output slot.
A standard Assembler uses 15 MW while operating. This is the Assembler’s consumption alone. If Miners, Smelters, Constructors, or other machines share the grid, include their use when checking capacity.
If hand-feeding works but the belts do not sustain production, check the transport route before changing the recipe or unlocking the Assembler. If it will not start by hand either, check power, recipe selection, and the required amounts for both inputs.
Connect one belt for each material
- Connect a belt from a storage container holding only Iron Plates to one input.
- Connect a belt from a separate container holding only Screws to the other input.
- Connect the Assembler output to a container for finished products.
- Open the interface and check that both Iron Plates and Screws arrive.
- Check that finished products continue to be carried out.
Starting with containers lets you test connections without rebuilding the entire upstream line. However, production stops when their contents run out, so replace them with supply from Iron Plate and Screw Constructors for sustained production.
The left or right input is not fixed to a particular material. What matters is that both required materials arrive. For the first run, keep them on separate belts instead of mixing them; this helps avoid one input backing up and blocking the other.
A rate of 5 per minute needs 30 Iron Plates and 60 Screws
| Standard recipe at 100% | Per minute |
|---|---|
| Iron Plates consumed | 30 |
| Screws consumed | 60 |
| Reinforced Iron Plates produced | 5 |
One Constructor for each input is not enough. One Iron Plate Constructor makes 20/min, and one standard Screw Constructor makes 40/min. Each supplies only two-thirds of the required amount, which explains why the Assembler waits for materials at that rate.
For 100% operation, one option is to use two Constructors for Iron Plates and two for Screws, merging each material’s output. You also need to supply each Constructor with enough Ingots or Iron Rods. For mining and smelting preparation, see Your first automated iron smelting line.
The final belt on the Screw side uses the full 60 items/min limit of Mk.1. Splitting it to another machine along the way reduces the supply to this Assembler. Check stored stock separately from whether the required amount arrives per minute.
Narrow down the cause by how production stops
| What you see | What to check next |
|---|---|
| Production never starts | Power, standby, standard Reinforced Iron Plate recipe, 6 Iron Plates and 12 Screws |
| Screws run out and the machine waits | Rod supply to the Screw Constructor and the 60/min route to the Assembler |
| Iron Plates run out and the machine waits | Iron Plate production and distribution to other machines |
| Finished items accumulate and production stops | Output belt connection and free space in the destination container |
| It runs for a while from a container, then stops | Whether the input stock has run out |
| Everything stops after adding machines | Total grid capacity and the breaker |
Speeding up an Assembler that is waiting for materials does not increase its incoming parts. Check Supply rates and belt limits before overclocking to decide whether to expand upstream production or match the clock speed.
If power capacity is the constraint, starting a Coal Generator for the first time is another next step.
Once you can use an Assembler, continue to Completing Space Elevator Phase 1 with 50 Smart Plating. Building the elevator itself is not enough; you must also package and send the delivery.
Sources and references
- Coffee Stain | Satisfactory 1.2 Update Out Now!
- Satisfactory Wiki (Japanese) | Production buildings
- Satisfactory Wiki (Japanese) | Milestones
- Satisfactory Wiki (Japanese) | Rotor
- Satisfactory Wiki (Japanese) | Reinforced Iron Plate
- Satisfactory Wiki (Japanese) | Iron Plate
- Satisfactory Wiki (Japanese) | Screw
- Satisfactory Calculator | Reinforced Iron Plate
- Satisfactory Wiki (Japanese) | Logistics
Questions and contributions
Share questions, corrections or play reports. Only approved posts for this article and language appear here.
Submit for review
Do not include personal details, passwords or private information about others. Text only. Publication and replies are not guaranteed.