Scope: PC full release 1.2 series, standard building costs, no mods. This covers using early FICSIT Foundations to connect to an existing piece and expand a small work area. PC controls use the default key bindings.

Complete Base Building and set aside materials for building

Foundations unlock through the Tier 1 “Base Building” Milestone after HUB Upgrade 6. Submit 200 Concrete, 100 Iron Plates, and 100 Iron Rods. Complete both submission and launch at the HUB Terminal.

Basic Foundations are available in 1 m, 2 m, and 4 m thicknesses. An early FICSIT Foundation costs 5 Concrete and 2 Iron Plates per piece. Changing its thickness does not change the cost of this basic Foundation.

  1. Select Base Building and submit the materials for the Milestone.
  2. After unlocking it, check that Foundations appear in the build menu.
  3. Carry Concrete and Iron Plates separately for construction.
  4. At first, expand using pieces of the same thickness and material.

If you used all the materials for the Milestone, you still cannot place Foundations after unlocking them. For example, 10 basic Foundation pieces require an additional 50 Concrete and 20 Iron Plates for construction. If you unlock and use a different material type, check its construction cost on screen.

Choose the first piece and connect from its edge

Rather than covering the whole factory at once, start with a work area large enough for a few machines and a path. Place the first piece at a height that is less likely to be buried by uneven terrain or rocks.

  1. Select a basic Foundation in the build menu.
  2. Choose the position and direction of the first piece and build it.
  3. Align the next Foundation candidate with an edge of that piece.
  4. Add it after confirming that it connects to the same floor surface.
  5. Expand from the edge you have built instead of placing every piece separately on the ground.

Foundations can connect to neighboring Foundations. Floors placed independently at separated points on the ground may not align perfectly in height or direction even if you later bring them close together. For an initial work area, expanding from one reference piece reduces the number of places you may need to correct.

When mixing Foundations of different thicknesses, check that their top surfaces align. Do not place a long run at once just because the pieces look similar; walk across the seams to check for a step before extending farther.

Use Zoop for a short row, then expand the floor one row at a time

Zoop is a mode for placing supported building pieces in a row. With basic Foundations, you can place up to 10 in one action. It does not create a 10-by-10 floor or a complete factory setup in one action.

  1. With a Foundation selected, press the default PC R key to change build mode.
  2. Check that the mode indicator says Zoop.
  3. Align the start of the row with an edge of an existing Foundation.
  4. Set the starting point with the build action and extend the preview in the direction you want.
  5. Check the number of pieces, their direction, and required materials, then confirm the row.
  6. Expand an adjacent row by connecting it to the edge of the Foundations you have placed.

You can also hold R to select a mode from the build-mode menu. If you changed the key binding, check the build-mode control shown at the bottom of the screen.

For the first try, make a short row and extend it only after confirming its height and direction. Distinguish the placement preview from the row that has actually been built, then confirm that it forms a walkable floor.

Leave room for machine inputs and paths before placing equipment

Once the floor is built, preview machine placement and plan the layout. Foundations make it easier to line machines up, but placing them in a row does not connect belts, Power Lines, or recipes automatically.

Check machine inputs and outputs first and leave room on the sides where belts will run. Avoid filling every edge with machines and then rebuilding everything to add paths or connections.

  1. Check the orientation and inputs and outputs of one machine.
  2. Leave a route to the next machine or container.
  3. Keep a path open so you can access machine interfaces.
  4. Connect belts and Power Lines, then test production with a small amount of material.
  5. If it works, expand in the same direction.

For a first production check, use Connecting a Miner to a Smelter and container. When building an upper floor, also check Conveyor Lift direction and connections.

What to check when placement fails or heights do not match

StateWhat to review
Foundations are missing from the build listDid you finish submitting and launching the Base Building Milestone?
One piece places but a long row will notTotal materials for the row and the reason shown in the placement preview
You can place only one piece at a timeDid you select Zoop instead of remaining in the default mode?
A step appears between adjacent floorsAre thickness, placement surface, and connecting edge aligned?
Separately built floors will not connectDo their initial heights and directions match?
Machines on the floor do not runCheck inputs, recipe, power, and output, not the Foundation itself

Do not try to fix two separated floors by continuing to extend them with Zoop. At the small early stage before placing machines, decide which floor will be your reference.

If trees on the ground are in the way, you can use the Chainsaw and Solid Biofuel. First make a small floor and one usable production line, then expand your factory!

To make a route between distant factories, see Setting up entrances and power at both ends of a Hypertube.

Sources and references

Questions and contributions

Share questions, corrections or play reports. Only approved posts for this article and language appear here.

Submit for review

Do not include personal details, passwords or private information about others. Text only. Publication and replies are not guaranteed.