This guide covers the PC full release 1.2 series, standard power consumption, and machines at 100% clock speed. It covers an early-game factory without batteries or Coal Power and with no mods.

Check fuel, capacity, and wiring in that order

Do not decide to add generators just because the machines look stopped. Refill fuel if it is empty, reduce the load or add capacity if the grid is overloaded, and fix the wiring if a machine is disconnected.

SituationCheck first
The factory-wide breaker trippedFuel and capacity of generators on the same grid
It trips again as soon as you add fuel and restartDoes the consumption of machines starting up exceed capacity?
Only some machines have no powerIs there a connected wire from each machine to a Power Pole and generator?
Adding a generator does not increase capacityIs the new generator connected to the same grid as the factory?

Fuel in your inventory is not used automatically. Check that it is in each Biomass Burner’s fuel slot. If you have several, refill each one and do not overlook the others after filling just one.

Distinguish the HUB’s 20 MW from a standalone unit’s 30 MW

Biomass Burners included with HUB progression and standalone Biomass Burners you build have different capacities.

TypeGeneration capacity per unitHow to add fuel
HUB-attached20 MWManual refilling
Standalone Biomass Burner30 MWManual refilling or belt delivery

A standalone Biomass Burner is unlocked by Tier 0 HUB Upgrade 6. If it is not in your build menu, complete the HUB delivery first.

Generation capacity adds up for generators connected to the same power grid. For example, one HUB-attached unit and one standalone unit provide 20 + 30 = 50 MW under standard conditions. Placing one on a separate, distant grid does not give your current factory 50 MW.

If this example factory needs 45 MW, it is within capacity. Add enough machines to exceed 50 MW, however, and the grid will be short. Do not judge by the number of generators alone; check the graph for the grid they are actually connected to.

Fix the cause, then restart with the lever

  1. Go to a generator or Power Pole connected to the grid and press E to open its screen.
  2. Check and refill the fuel in each Biomass Burner.
  3. If capacity is insufficient, put nonessential production machines on standby or add generators.
  4. Connect any new generator to the same grid as the factory you want to restore.
  5. Drag the Circuit Breaker lever down in the power screen to restart.
  6. After production machines start, check that the breaker does not trip again immediately.

Repeatedly using the reset control does not fix a fuel shortage or overload. If it trips again right after restarting, stop more machines to lower the load or add available generation capacity before trying again.

If you are short on ore and cannot make materials for the repair, use a Portable Miner that needs no power to collect materials.

Read the power graph as “now” and “everything running”

Consumption is current use, Capacity is available generation, and Max Consumption is the draw if every connected machine runs. If the UI is in English, use these three labels as a guide.

Consumption may be low while the factory is waiting for materials, but machines will start once materials arrive. For stable operation after restarting, aim for a setup where the power use of all machines running at once stays within Capacity.

Biomass Burners throttle output to match demand, so Production being below its maximum does not by itself mean they are broken. Distinguish low current output from a reduced available capacity caused by running out of fuel.

Avoid repeating the outage with refills and wiring

Processing Leaves or Wood into Biomass, and later into Solid Biofuel after unlocking it, can extend the time between refills. Changing the fuel type does not increase the standard 20 MW or 30 MW capacity per burner.

Standalone units can receive fuel on a belt, but the HUB-attached burner does not have the same input port. A standalone burner also stops receiving fuel if the supply feeding its belt runs out. During recovery, putting fuel directly into the burner first and then checking its supply source can make the troubleshooting order clearer.

For early wiring, use the basic pattern “generator → Power Pole → machines.” Version 1.2 also has a feature that connects machines to each other in a daisy chain, but it requires research at the MAM. Before that research is available, branch wires from Power Poles instead of repeatedly trying to select a machine that cannot be connected that way yet.

Once power is stable, continue to connecting a Miner and Smelter for your first Iron line. If you later make Coupons at the AWESOME Sink, remember to account for the Sink’s 30 MW consumption.

To gather more vegetation for fuel, see preparing a Chainsaw and Solid Biofuel. At Tier 3, Coal Power with Coal, water, and startup power can reduce the work of refilling burners.

Sources and references

Questions and contributions

Share questions, corrections or play reports. Only approved posts for this article and language appear here.

Submit for review

Do not include personal details, passwords or private information about others. Text only. Publication and replies are not guaranteed.