Scope: Java 26.3 series in normal Survival, with no experimental features or mods. This guide covers draining a small, partitioned body of water by hand after obtaining a sponge.

Start with a dry sponge

There are two items: a Sponge and a Wet Sponge. The dry Sponge is the one that absorbs water. Do not judge only by its yellow appearance; check the item name in your inventory.

There is no recipe to craft a new sponge in the standard crafting system. Obtain wet sponges from a sponge room in an ocean monument or as a drop from an Elder Guardian, then dry them for use. Some monuments have no sponge room, so do not expect every monument to contain a large supply.

Drainage preparationUse
Dry spongeRemoves water
Sand or other partition blocksBlock incoming water and reduce the work area
HoeBreak and retrieve a used sponge faster
Furnace and fuelRestore a wet sponge so it can be reused

For your first test, check absorption and retrieval in a small pool. It is easier to focus on the work if you do not try to drain a large area while leaving monument enemies alive.

Seal the outside and make small compartments before placing it

If you place one sponge in the open ocean, water flows in from the surrounding sources. A sponge also has a limit to how much water it can absorb, so first separate the work area from outside water.

  1. Decide which area you want to drain.
  2. Build partitions from the bottom to the water surface and close gaps where water can enter from the sides.
  3. Divide the inside into smaller compartments if the area is wide.
  4. Place a dry sponge where it touches the water in a compartment.
  5. Watch where remaining water comes from and fix gaps or compartments that are too large.
  6. Retrieve the wet sponge and use a dry one to remove the remaining water.

Do not build the partition only at the water surface; check for gaps underwater too. Even if the surface looks enclosed, water will flow in if the bottom is still connected to the outside.

Sand is easy to stack from above, but stand clear of the area where it will fall. Finish one small compartment first and confirm that it drains before expanding the work area.

If water returns, check the source of inflow before adding sponges

If water returns to the same place right after absorption, the sponge is not necessarily broken. Water may be flowing in from a source left outside or inside the compartment, creating water again.

Before placing sponges everywhere, check for gaps in the partitions and locate the remaining water. If a compartment is too large, divide it further before absorbing the water. In deep areas, water above you may remain, so remove water from higher sections first.

A bucket removes one water block, while a sponge is used to remove water across a surrounding area. The way a water source reforms is also covered in how a 2×2 infinite water source works.

Remove an interior partition only after draining the neighboring compartment too. If you break the enclosure that borders the ocean too early, water will refill the area you just drained.

Dry it in a furnace and retrieve the result

  1. Retrieve the wet sponge.
  2. Open a regular furnace.
  3. Put the wet sponge in the upper input slot and fuel in the lower fuel slot.
  4. When drying finishes, take the sponge from the result slot on the right.
  5. Bring it back to the compartment you want to drain and use it again.

Do not leave a wet sponge placed in the world and wait for it to dry; process it in a furnace. You can retrieve and dry a used sponge, so you do not have to search for another monument for every drainage job.

Keep dry and wet sponges in separate inventory or storage locations to avoid selecting the wrong one. If you need to pause, dry the next sponge before returning to the work.

In the Nether, place it after bringing it there

If you have a safe Nether base and a reliable way to travel back and forth, you can also dry a wet sponge by placing it as a block.

  1. Bring a hoe and wet sponges, then travel to the Nether.
  2. Place a wet sponge on a safe surface with solid footing.
  3. When it changes into a dry sponge, break and retrieve it.
  4. Check the item name, then return to the area you are draining.

Simply carrying it through a portal in your inventory does not dry it. Do not throw it into lava; place it as a block on a solid surface. If you are not ready for the trip, first prepare a Nether return route and protected portal (Japanese article) or use a furnace instead.

Do not apply the behavior of dry biomes in Bedrock Edition to the Java Edition steps here. In Java Edition, use a furnace or place the sponge in the Nether as described above.

Check these points if it does not absorb or dry

ProblemWhat to check
It does not absorb water when placedDid you select a wet sponge, or is it touching water?
Water quickly returnsOutside inflow, remaining water sources, or a compartment that is too large
The furnace does not runInput and fuel slots, and whether the result slot is clear
It is still wet after going to the NetherDid you place it as a block, instead of just carrying it?
It is slow to breakUse a hoe. Also check for underwater or mining-fatigue effects.

For underwater work, activating a Conduit can help. However, draining the water around the Conduit will deactivate it, so keep the drained area separate from its location.

Sources and references

Questions and contributions

Share questions, corrections or play reports. Only approved posts for this article and language appear here.

Submit for review

Do not include personal details, passwords or private information about others. Text only. Publication and replies are not guaranteed.