To carry an Iron Plate line across another belt without mixing the two, place one pair of underground belt entrances and exits. You do not need ordinary belts in the underground span. First test a short crossing and confirm that items entering one side emerge from the other.
Scope: PC 2.0.77, base game, normal quality, no mods, mouse and keyboard. This is a first crossing using yellow underground belts. It does not cover Space Age, additions in 2.1, or in-game testing.
Research Logistics and craft an entrance and exit
| Preparation | What you need | Check |
|---|---|---|
| Research Logistics | 20 Red science packs | Unlocks underground belts and splitters |
| Craft one batch of underground belts | 10 Iron Plates and 5 Transport Belts | Produces 2 Underground Belts |
| Connect to | Ordinary yellow belts | Provide flow before the entrance and after the exit |
Use the 2 finished Underground Belts as the entrance and exit. The 10 Iron Plates in the recipe do not include the Iron used to craft the Transport Belts. The 20 Red science packs are the cost for Logistics alone. Even if you can already craft ordinary belts, Underground Belts separately require Logistics research.
Yellow Underground Belts move items at the same speed as ordinary yellow belts and need no power. If items stop flowing, check the entrance, exit, and destination in that order instead of adding a power pole.
Cross one belt line in 6 steps
- Choose the line to cross. In this example, Iron Plates travel east, and a separate line runs north to south across the route.
- Prepare 2 Underground Belts. After researching Logistics, craft one batch and use the pair for the entrance and exit.
- Place the entrance before the other line. Set it to face east and connect an ordinary belt on the side where the Iron Plates enter underground.
- Place the exit on the same straight line. Put it on the ground beyond the other line; check the connection indicator and that its output points east.
- Connect the downstream belt. Run an ordinary belt from the exit to the pickup point, leaving space after the exit.
- Check items entering and leaving. The short crossing is complete when Iron Plates enter underground and appear at the exit without mixing with the other line.
To change direction or fix the entrance and exit, use the default R rotation control on a placed Underground Belt. This can also switch which end is the entrance and which is the exit, so check the tunnel-entry and tunnel-exit sides rather than treating it exactly like rotating an ordinary belt. If you changed the key, use its current binding in Settings.
This short test is an editorial suggestion. Confirm one connected pair before trying layouts that weave multiple underground lines together or take items from only one lane.
Count the yellow 4-tile span between the endpoints
Yellow Underground Belts can span up to 4 tiles underground. The 2 tiles occupied by the entrance and exit are not part of those 4. At maximum length, the layout is “entrance, 4 tiles between, exit,” for 6 tiles total. Do not count 4 tiles including both endpoints, or leave 5 tiles in between.
For your first setup, cross a single north-south belt over a short distance and check the connection indicator as you place the belts. Use the same type for both endpoints. A red exit does not connect as a pair with a yellow entrance.
Underground spans can also cross other underground belts and pipes, but their contents do not mix. Check the positions, directions, and distance between the two surface endpoints. Do not extend this ordinary surface-belt procedure unchanged to space or lava.
Diagnose the cause by where items stop
| Where items stop | What to check | Fix in this order |
|---|---|---|
| Iron Plates do not reach the entrance | Direction and supply of the preceding ordinary belt | Send items to the entrance |
| Items back up at the entrance | Straight alignment, belt type, and distance to the exit | First restore a short pair of the same type |
| Items stop after emerging from the exit | Downstream belt or pickup point is full | Make room downstream |
| One side of a side-fed input stops | Whether items are hitting the tunnel-side half | For the first test, feed from directly in front of the entrance |
| Items mix with another belt | Whether ordinary surface belts are joined together | Check where the belt enters and exits underground |
Side-loading an Underground Belt depends on whether that tile exposes the belt or the tunnel side. Do not assume a stopped lane means the underground span has failed.
For taking items from furnaces and feeding an Assembling Machine, check the Inserters too. If your goal is to split the flow rather than cross another line, see splitter priorities and filters.
To increase throughput, continue to upgrading to red belts and checking where yellow belts remain.
Sources and references
Questions and contributions
Share questions, corrections or play reports. Only approved posts for this article and language appear here.
Submit for review
Do not include personal details, passwords or private information about others. Text only. Publication and replies are not guaranteed.